Home Page
|
Terms & Conditions
|
View Basket Contents
|
Go to the Checkout
|
Contact Us
We value your feedback
Click here to make suggestions
Panel Adhesive - 380ml
Construction Chemicals Panel Adhesive is a general purpose, gun grade, high bond strength synthetic rubber/resin adhesive with good gap-filling properties. It has high initial grab and can be used for fixing battens and wallboards directly onto walls without other fastenings.
· Safe and easy to apply from cartridges with integral nozzles
· Bonds a wide range of materials including wood, wall claddings and metals
· High initial grab
· Excellent gap filling properties
· Excellent bond strength
GENERAL USES
· Ideal for bonding most types of wall cladding direct to internal wall surfaces or timber battens
· Can be used for fixing battens directly onto walls without other fastenings
· Ideal for fixing rigid PVC architraves and skirtings to wall surfaces
· Can be used for bonding carpet gripper systems to most sub floors without the use of tacks or nails
· Ideal for bonding stair nosings to concrete and wood stairs
· Can be used for securing aluminium and other skin panels to the framework of portable industrial buildings and caravans
METHOD OF USE
All substrates must be dry and free from dust, grease and any loose material. Paint should be removed where the adhesive will make contact.
N.B. New concrete or plaster should be allowed adequate time to dry and mature.
Porous or friable surfaces should first be primed with a dilute solution of contact adhesive and allowed to dry. Apply the Construction Chemicals Panel Adhesive as a bead approximately 6mm diameter to one surface to be bonded and firmly press the materials together. A firm bond is achieved in about 1 hour.
TYPICAL APPLICATIONS
To bond flat panel direct to walls
Apply Construction Chemicals Panel Adhesive as a bead approximately 6mm diameter around the periphery of the panel (50mm from the edge) and in horizontal lines at approximately 450mm centres. Immediately press the panel firmly to the wall surface to ensure adequate transfer of adhesive and leave to set. A firm bond is achieved in about 1 hour.
N.B. If panel is warped, apply adhesive as described and the press the panel firmly to the wall surface and pull away immediately. This will achieve an adhesive transfer and allow quicker solvent evaporation. After 10 – 20 minutes, the panel may then be bonded into position and a contact bond achieved.
To bond stair nosings
Apply Construction Chemicals Panel Adhesive as a 6mm diameter bead to the stair nosing only – 2 or 3 beads may be necessary depending on the size of the nosing. Immediately press the nosing firmly into position to ensure adequate transfer of adhesive to the stair tread. If a higher initial bond strength is required, press the nosing into position and then pull away to effect adhesive transfer. Allow adhesive to dry apart for 10 – 20 minutes before pressing finally into position. Allow to dry for 24 hours before subjecting to traffic.
SPECIAL COMMENTS
A lower viscosity version is available.
The above figures do not constitute a specification. They represent typical values obtained for this product.
HEALTH AND SAFETY
Before using this product, ensure that you have been supplied with and have read carefully the following information:
· The hazard label (complying with CHIP Regulations 1995) applied to the container
· Construction Chemicals Material Safety Data Sheet for this product
Construction Chemicals Panel Adhesive is classed as a Petroleum Mixture and a licence is required for storage etc.
TECHNICAL DATA
Base Synthetic Elastomer
Solids 73 – 79%
Viscosity Viscous paste
Colour Beige
Tack life 5 - 30 minutes
Coverage 11 metres per cartridge 6mm bead
Cleaner Solvent 1
Flash Point -18ºC
Shelf Life 6 months at 4 – 25ºC
Panel Adhesive Health & Safety & Technical Data Sheet
Price:
£2.66
excluding VAT
Quantity:
1.
Oxalic Acid
Size - prices exclude VAT
25 kg - £77.00
5 kg - £22.00
Quantity:
2.
Envirosafe One Shot Injection Cream (DPC)
Size (prices exclude VAT)
5 Litres - £68.20
2 * 5 Litres - £67.10 each
5 * 5 Litres - £60.50 each
1 * 1 Litre - £17.16
6 * 1 Litre - £16.94 each
12 * 1 Litre - £16.50 each
380cc cartridge - £10.45
5 * 380cc cartridges - £8.64 each
10 * 380cc cartridges - £7.81 each
Quantity:
3.
Tanking Slurry - 25kg
Price:
£49.50
excluding VAT
Quantity:
4.
Wood Weld PU - 310ml
Number of Cartridges (prices exclude VAT)
One (£7.15)
Box of 12 (£5.48 per cartridge)
5 Boxes of 12 (£4.95 per cartridge)
11 Boxes of 12 (£4.40 per cartridge)
Quantity:
