Home Page
|
Terms & Conditions
|
View Basket Contents
|
Go to the Checkout
|
Contact Us
We value your feedback
Click here to make suggestions
Mitre-Mate Cyanocrylate Adhesive - 50g (incl. activator) Superglue
Construction Chemicals Mitre-Fast Cyanoacrylate adhesive is an ethyl Cyanoacrylate adhesive of high viscosity. It is especially suitable for bonding irregular or porous components with excellent gap filling properties.
APPLICATIONS
· Specially formulated for kitchen fitting application
· An excellent general purpose grade
· Bonding of MDF and veneered wood surfaces
· Bonds in seconds; rubbers, plastics, metals and ceramics
BENEFITS
· Single component adhesive
· 100% solvent-less
· Slower cure allows adjustment during assembly
· High impact strength
· Vertical surface use, plus gap filling up to 0.25mm
PERFORMANCE DATA, TYPICAL VALUES
Steel/Steel substrate values
Tensile strength (ASTM D2095) 22-26 N/mm² (3600-4400 lbf/in²)
Tensile shear strength (ASTM D1002) 13-18 N/mm² (2300-2700 lb/in²)
Impact strength (ASTM 950) 2 – 2.5 N/mm² (9-11 lb/in²)
Physical properties of liquid adhesive
Monomer Ethyl cyanoacrylate
Appearance Colourless
Specific gravity 1.08
Viscosity @ 25ºC (Brookfield) 1300 – 1700 cPs
Flash point (Cleveland open cup) > 85ºC
Shelf life (Stored below 25ºC) 12 months minimum
Toxicity Non-toxic
Physical properties of cured adhesive
Refractive index (ND20) 1.46
Hardness (Rockwell) 85
Specific resistance OHM/cm 8 x 1012
Dielectric constant @ 1MHZ 3.44
Softening point 150ºC
DIRECTIONS FOR USE
seconds or as indicated below. Cure speed is rapid, so exercise care when aligning. Cure performance
can be enhanced if necessary, by using selected activators.
TYPICAL BONDING TIMES
Wood (mdf) up to 10 seconds
Plastics 5 – 60 seconds depending on substrates
Rubbers 2 – 20 seconds depending on substrates
Metals (degreased) 10 – 60 seconds depending on substrates
LIMITATIONS
Ensure surfaces are degreased prior to bonding.
Ensure surfaces are close fitting.
This product is not suitable for permanent glass bonding, or applications where the bonded joint may be immersed in water.
RELATIVE HUMIDITY CONDITIONS
Where possible, the working environment should have a relative humidity of 50%+.
CAUTION
Prior to use, consult relevant Material Safety Data Sheet.
When continuously used, local fume extraction is recommended.
Contains Cyanoacrylate ester. Use in a well-ventilated environment.
In the event of inadvertent skin bonding, separate bonded skin tissue carefully by peeling apart gently with a blunt instrument, preferably after soaking in warm soapy water.
Keep out of reach of children.
STORAGE
Store in original sealed upright container between +3ºC and 20ºC in a dry area out of direct sunlight.
The lower the temperature, the longer the ultimate shelf life, but bring to room temperature before use.
PACKAGING
Available in 50g packs.
DISCLAIMER
Construction Chemicals accepts no liability for loss or damage arising directly or indirectly from the use of this product. The data given is for information only and is based upon data we believe to be accurate and reliable. Before using any product, it is the customer’s responsibility to satisfy themselves by appropriate trials that each product is suitable for their intended use. As the application and use of the product is outside the control of Construction Chemicals, the user assumes all risk and liability whatsoever in connection herewith.
All materials supplied are subject to our standard terms and conditions of trading, a copy of which is available upon request.
Working temperature range -55ºC to +80ºC
Mitre-Mate Health & Safety & Technical Data Sheet
Price:
£10.82
excluding VAT
Quantity:
1.
Oxalic Acid
Size - prices exclude VAT
25 kg - £75.00
5 kg - £25.00
Quantity:
2.
Envirosafe One Shot Injection Cream (DPC)
Size (prices exclude VAT)
5 Litres - £62.00
2 * 5 Litres - £61.00 each
5 * 5 Litres - £55.00 each
1 * 1 Litre - £15.60
6 * 1 Litre - £15.40 each
12 * 1 Litre - £15.00 each
380cc cartridge - £9.50
5 * 380cc cartridges - £7.85 each
10 * 380cc cartridges - £7.10 each
Quantity:
3.
Tanking Slurry - 25kg
Price:
£45.00
excluding VAT
Quantity:
4.
Wood Weld PU - 310ml
Number of Cartridges (prices exclude VAT)
One (£6.50)
Box of 12 (£4.98 per cartridge)
5 Boxes of 12 (£4.50 per cartridge)
11 Boxes of 12 (£4.00 per cartridge)
Quantity:
