We value your feedback

Click here to make suggestions


Gripfill - 350ml Gripfill - 350ml
Gripfill is a solvent-borne, filled rubber resin adhesive developed to bond virtually any rigid material together regardless of the evenness of the surface.

USES
Gripfill is a high strength, one part, gap filling adhesive specially formulated to bond a large variety of materials such as plywood, block wood, chipboard, hardboard, laminated plastics, rigid uPVC (excluding foamed PVC), rigid insulation materials (excluding polystyrene), metal sheeting including aluminium, steel, galvanised iron, tin plate and non-ferrous metals, to themselves or to brick, stone, breeze block, sand/cement screeds, concrete, plaster, plasterboard and insulation boards.

Where Gripfill is used externally, it must be protected from driving rain, ponding water or permanently wet situation. This can be achieved by sing a suitable silicone sealant.

Gripfill is not recommended for bonding mirrors.

PREPARATION
Surfaces to be bonded must be clean, structurally sound, dry and free from dust or loose material. Porous surfaces such as plaster and fibre cement board should first be primed using PVA diluted 5:1 with water and allowed to dry thoroughly before Gripfill is applied.

APPLICATION
a) Stair nosing, window frames etc - Apply a continuous bead approx. 6mm diameter to the surface being bonded. Position on the substrate, if possible by sliding into place and apply pressure overall. If the object is to e applied to a vertical surface, temporary mechanical support may be required.

b) Wall panels – For most work, Gripfill should be applied as a 6mm bead diameter to the rear of the panel. Extrude a continuous bead around the panel approximately 25mm from the edge. Additional beads should then be applied across the panel at 600mm centres (450mm for heavy panels). Immediately present the panel to the wall slightly above its required position and applying pressure slide it into place in order to break any surface skin. Press firmly to ensure maximum overall contact, using a soft mallet if necessary. Any adjustment must be made within the first five minutes of placing. Alternative, Gripfill may be applied in blobs approximately 10-12mm in diameter at 300mm centres. This is not recommended for bonding plastic materials.

c) Impervious materials – Where two impervious materials are to be bonded, apply Gripfill as above, press firmly together and break the bond by pulling away immediately ensure good transfer has occurred. Wait a maximum of five minutes and re-bond the two materials

SAFE HANDLING PRECAUTIONS
Flammability: Highly flammable.
Keep away from sources of ignition including pilot lights and sparks.
Take precautionary measures against static discharge.
Unsure thorough ventilation. Do Not Smoke.

Gripfill Health & Safety & Technical Data Sheet
Number of Cartridges (prices exclude VAT)
Box of 12 (£2.55 each)
One (£2.64 each)

Quantity:  

 




 
Oxalic Acid
1. Oxalic Acid

Size - prices exclude VAT

Quantity:

Envirosafe One Shot Injection Cream (DPC)
2. Envirosafe One Shot Injection Cream (DPC)

Size (prices exclude VAT)
5 Litres - £68.20
2 * 5 Litres - £67.10 each
5 * 5 Litres - £60.50 each
1 * 1 Litre - £17.16
6 * 1 Litre - £16.94 each
12 * 1 Litre - £16.50 each
380cc cartridge - £10.45
5 * 380cc cartridges - £8.64 each
10 * 380cc cartridges - £7.81 each

Quantity:

Tanking Slurry - 25kg
3. Tanking Slurry - 25kg


Price:    £49.50
excluding  VAT

Quantity:

Wood Weld PU - 310ml
4. Wood Weld PU - 310ml

Number of Cartridges (prices exclude VAT)
One (£7.15)
Box of 12 (£5.48 per cartridge)
5 Boxes of 12 (£4.95 per cartridge)
11 Boxes of 12 (£4.40 per cartridge)

Quantity: